Tds-patched.tar.gz

Tds-patched.tar.gz - Free Download

This low odor, masonry paint is formulated for waterproofing above and below grade basement walls, masonry walls, retaining walls, cinder and concrete blocks, stucco and brick. It uses nanotechnology to form a barrier to help stop water infiltration. This alkali resistant coating provides a long-lasting, durable and decorative finish. Not for use on floors or on walls with active water leaks. Test for loose, flaking concrete by pressing a piece of masking or cellophane tape at various places, then pull it off with an abrupt action.

If the tape does not pull the concrete from the surface, it can be painted. If the existing concrete is removed, the loose concrete should be removed down to a sound substrate. For below grade application: All holes or cracks must be properly patched with a fast-setting hydraulic cement. For above grade application: Remove mildew stains with a mildew stain removing product.

All surfaces must be clean and free of dirt, dust, efflorescence and oil. Apply to dry or slightly damp masonry walls. Wipe off any visible moisture with a dry cloth before painting. A minimum of two coats are required: Using a brush or roller, work the waterproofer onto the surface until any all pores or voids are covered. Using a brush or roller, cover the entire surface.

Properly fill any voids left after the first coat. Additional spot application may be needed depending on the porosity of the surface. If leaking is still present after two coats, it indicates that voids or pinholes are still open.

Re-apply product to these areas. Do not apply at a greater spread rate. Wait 1 hour dry to touch; 4 hour recoat. Low temperatures or high humidity conditions will affect drying time.

Full cure should be reached in days. Fully cured coating can be washed after days. Clean equipment and paint spatters with warm, soapy water.

If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current governmental regulations. Do not dispose of this product down a drain. For recycling or disposal information contact your local household refuse collection service.

Avoid applying in direct sun. If the surface is hot to the touch it should be considered too hot to apply this coating. Masterchem Industries LLC warrants to the original residential consumer purchaser the performance of this product as described on this label for 10 years on vertical and horizontal surfaces, from the date of purchase, for so long as you reside in your home.

This warranty is not transferable. If this product is found not to perform as specified upon inspection by our representative during the warranty period, Masterchem Industries LLC will, at its option and upon presentation of proof-of-purchase the original receipt , either furnish an equivalent amount of new product or refund the original purchase price of this product to you.

This warranty excludes 1 labor and costs of labor for the application or removal of any product, and 2 any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

If you scrape sand or remove old paint, you may release lead dust. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at LEAD or log on to www.

This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm. Sealed surfaces may become slippery when wet. Use caution when walking on surface when moisture is present. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air and use a properly fitted respirator NIOSH approved for zorganic vapor with P Series particulate prefilter.

Obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use. Does not include the loss of material from spraying. New or Unpainted Surfaces: New concrete must cure for a minimum of 30 days. Stir well before use. Use with adequate ventilation. Dry Time Wait 1 hour dry to touch; 4 hour recoat.

Allow two weeks before washing or cleaning for full cure. Shelf life under normal conditions is two years unopened. Limited Warranty Masterchem Industries LLC warrants to the original residential consumer purchaser the performance of this product as described on this label for 10 years on vertical and horizontal surfaces, from the date of purchase, for so long as you reside in your home.

First Aid If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 20 minutes and get medical attention; for skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately. Coverage - Low 75 sq.

tds-patched.tar.gz

Connect PHP in Debian Jessie to Ms Sql Server using FreeTDS

We suspected it since little had changed on our Linux box and that patch was related to TLS handshake. Tundra Solutions Forums Archive Top. Sending packet [blah blah] login. Wait for the locks to cycle again and then release the button to complete the resetting and reprogramming sequence. After trial and error, I had the opposite experience from Peter Hanley that is documented in one of the above posts, although as Peter points out, the error is a bit different. Full cure should be reached in days.

Sealcoating Contractors Charlotte, NC | Parking Lot Maintenance | Asphalt Repair

Locate Installers Contact a Location. Sign up or log in Sign up using Google. Coverage - Low 75 sq. If leaking is still present after two coats, it indicates that voids or pinholes are still open. Turn the key in the ignition on and then off. When Garrett comes out, Artemus is outside waiting for him, asking Garrett to give him the Artifacts. Share Share this post on Digg Del. The lair is located in Audale's underground. If spilled, contain material and remove with an inert absorbent. All holes or cracks must be properly patched with a fast-setting hydraulic cement.

Primary Menu

tds-patched.tar.gz

Paint only clean, dry, and sound surfaces. Using a brush or roller, work the waterproofer onto the surface until any all pores or voids are covered. Since the issue is no longer occurring after uninstalling that KB update resolved the issue, I did a quick search on that KB update for prior cases. Remove mildew stains with a mildew stain removing product. Not for use on floors or on walls with active water leaks. Avoid contact with eyes and skin. Does not include the loss of material from spraying. For above grade application: Password Please enter a password for your user account. Close the door 8. Clean up carefully with a HEPA vacuum and a wet mop.

Summary
Review Date
Reviewed Item
Tds-patched.tar.gz
Author Rating
51star1star1star1star1star

Leave a Reply

Your email address will not be published. Required fields are marked *